Список продуктов

KJT-PK Wireless System Deviation Switch
KJT-PK Wireless System Deviation Switch

Переключатель отклонения беспроводной системы KJT - PK

  • Серия продуктов:KJT-PK wireless system deviation switch
  • Загрузочный ток:AC380V 5A,DC24V 5A
  • Контактная информация:NO1.NC1 НО2.NC2. (При заказе укажите)
  • Режим сброса:Автомобиль
  • Срок службы электроприборов:> 100 000 раз
  • Класс защиты:IP65 / IP67

88

МодельKJT-LS47CSZK (Wireless drawstring)
Protocol standardsLoRa private network protocol
Диапазон частот470~510MHz  FHSS
Maximum link budget162dB
Maximum output power20dBm
Polarization modeSingle polarization; vertical polarization
ЧувствительностьTransmission rateReceiving sensitivity (dBm)
2400bps-126dBm
800bps-130dBm
300bps-140dBm
Recommended transmission distance20-1000M


Manage

management styleSupports Chinese/English management and configuration without restarting;
resethardwaresupport
softwaresupport

Function

Operating modeP2P-S、M2P etc.
Enter configurationSupport 4 channels of IO (contact), support RS485 (optional), support wireless configuration parameters
Display and sensor buttonsDisplay (LED) waterproof type none
Sensor button (optional) waterproof type none
Display showsBattery status, connection status, signal strength, command status, device type
Real-time data status displaySupport real-time display of status of each IO port
Безопасность
wireless encryptionCPC verification AES128
hardware
CPUIndustrial grade MCU
MemoryFLASH16MB

SRAM32K
Main frequency48MHz

1. Fix the pull rope switch on the bracket, and then weld it to the frame;

2. The distance between the two machines is 55-60 meters, and they are connected by a steel wire rope with a diameter of Φ4, and the tightness should be moderate;

3. In order to reduce the influence of the weight of the wire rope on the switch startup, weld tow rings on the frame every 5-10 meters to support the wire rope;

4. Prioritize the installation of the antenna before starting up. After installation, press the waterproof switch to automatically find the host computer;

5. The wireless pull cord switch is paired and installed with the wireless gateway or host. The pairing process has been completed by default before leaving the factory. The device ID is affixed to the surface of the product and installed according to the corresponding point table.


Interface
СоединительNumber of sockets1
Connector propertiesM16 stainless steel waterproof switch
AntennaAntenna interfaceSMA
Antenna gain3dBi
Antenna angleVertically polarized omnidirectional antenna
powered by
Режим питанияLithium sub-batteryDC3.6v   6.5Ah
Механические параметры
AngleУгол действия30°
extreme angle60°
动作力10kg
Контактная информацияNormally open quantity2 way (default)
Normally closed quantity2 way (default)
ResetAutomaticLevel 1 alarm
ManualLevel 2 alarm
Micro SwitchOmron
usage count10^6
shell materialCast aluminum (default) Stainless steel (optional)
Вес3kg/3.5kg
Work environment and characteristics
Рабочая температура-20~60℃
Температура хранения-20~60℃
Humidity (non-condensing)≤95% (non-condensing)
signal input4-way IO (contact) RS485
РазмерL*W*H(mm)220*200*130
Рабочий токFull load operating current < 0.5mA @3.6V
Normal working current < 0.15mA @3.6V
Idle state operating current

 <0.05mA @3.6V

22

11

33


88

PK1

f85861ea63038614d36f58cc6993550

PK2

接线图.png

444

场景图

d25bccef52ed6fc24d8045760301c48

Рекомендуемые продукты